Resin Bound Permeable Paving for Pedestrian and Vehicle traffic

Product Description MTB-7910 2HRS  Resin Pound Permeable Paving for Pedestrian and Vehicle Traffic Features  38% of resin formulated from a botanic source UV stable non yellowing resin Product warranty up to 15 years available Natural appearance Recycled aggregates available  Highly permeable—up to 850 litres / m² / minute High slip resistance Suitable for pool surrounds,pathways,floor,garden, driveways, car parks and access roads Low maintenance Variety of colours Variety of  operation time Appliaction Suitable for decorative and protective coating and mixing with aggregates ,especially for the floor ,such as Garden  indoor floor &out door floor backyard  garage  swimming pool  wine celler balcony stairway pedestrian walkways  Livingroom,bedroom,bathroom Technical Data Sheet 

MTB-7910	A	B
Appearance	Clear/white Liquid	Clear Liquid
Viscosity(25°C,CPS)	2000-3000	500-700
Flash Point(°C)	>300	>150
Mix Ratio(P.H.R)	60	30
Curing Time	2H
Curing Condition	8-10H at room temperature 90mins at 70°C

   Coverage Data MTBJZJ Resin Bound Surfacing Resin                                      1.5kgs                     MTBJZJResin Bound Surfacing Aggregate(4~6mm)                100kgs Coverage @ 10mm                             6.5m² (approx) Coverage @ 15mm                           4.675m² (approx)  Coverage @ 18mm                           3.89m² (approx)  Coverage @ 20mm                           3.5m² (approx)     Physical Properties of HSG resin @ 20°C           Working Time                                                    40—55 minutes                                                  Lay Before Rain                                                4—4½ hours  Foot traffic after                                                1 3—14½ hours Light vehicle traffic after                                  1½—2 days Occasional heavy vehicle traffic after            7 days Notes:Site conditions will affect the times quoted. All data is provided as a guide only.    Instructions for Use New asphalt concrete should be left to cool and gain strength for not less than 24 hours @ 20ºC The surface of the asphalt concrete must be clean, dry and free from loose materials. Ensure that the mixing station is fully waterproof when rain is expected,discontinue mixing when fog or mist are anticipated. Light rain on the surface of the system is unlikely to damage or affect the surface, see later reference to application in rainy conditions. Place MTBJZJ Resin Bound Surfacing Aggregate into a clean, dry, forced action mixer  minimum capacity/ power 120 litres/ 1.8kW, Baron E200 mixer or similar. Scrape all of the contents of MTBJZJ Resin Bound Surfacing B component into the larger A component container and mix with a drill and helical paddle mixer attachment for 30-45 seconds. Keep mixing time to a minimum to avoid a build up of heat. Immediately add the mixed resin to the aggregate in the mixer.  Mix the aggregate and resin together until all the aggregate is evenly coated with resin. Keep mixing time to a minimum to avoid a build up of heat. Discharge the mixed resin and aggregate onto the prepared surface, level and smooth. Excessive compaction will reduce permeability. Finish the surface with a suitable float. If required, immediately cast MTBJZJ Resin Bound Surfacing Anti-Slip Aggregate onto the  top surface of the wet resin and aggregate, at the  rate of approximately 0.1kg/m². Ensure even coverage to prevent a patchy appearance. Allow to cure and open to traffic as described in Physical Properties. Working Temperatures Working time is affected by temperature; at temperatures above 25°C the pot life and working time may be insufficient to allow its proper application. Work should therefore not proceed when product and / or air temperature exceeds 25°C. The air temperature must therefore be monitored during application and work should stop when temperature is above 25°C.  Care must be taken to keep materials as cool as possible in warm weather.   Rain During Application Light rain on the surface of the system is unlikely to cause damage to or affect the surface. Heavy rain is likely to spoil the appearance of the surface. Very heavy rain could wash out resin and aggregate. Therefore application during rain or when rain is anticipated during the cure period is not recommended (see Physical Properties). Care must be taken to keep the mixing station dry, thus avoiding entrapment of moisture between aggregate and resin.   Shelf Life &Storage Shelf life of MTBJZJ Resin Bound Surfacing Resin is 6-12 months at least, aggregates have an unlimited shelf life. Store materials in clean, dry, frost free warehouse conditions between  5oC and 25oC. Protect from sunlight.   Mixed With Gravels & Pebbles       Final Application Show           Company Information About us  1. We are direct manufacturer of glue and adhesive since 1998. 2. Main articles we sell well are clear epoxy resin AB glue ,two components metal structural adhesive ,instant glue ,anaerobic adhesive ,N-times removable sticky notes glue ,glue dots ,UV glue ,OCA adhesive ,UV nail gel ,retaining compound Adhesive,hot melt adhesive ,PVC-ABS plastic glue ,magic stickers,no nail and mark wall hook,sticky screen cleaner ,mobile phone stickers and so on    3.The certificates we have gained are Patent of Removable Glue Dots ,SGS ,MSDS ,EC ,ROHS .   4.The factory audit we pass are SGS and Walmart audit.   Our Service Why choose us ? 1. Professional manufacturer & long  history We are direct manufacturer of glue and adhesive since 1998.So We have Professional production team, production line, experienced technical experts also much experiences and higher  skills to ensuring product quality and deliver in time with a very short time . 2. Competitive quality &factory price 3. Our market  Our customer all over the world . Main market in Europe ,South America,Australia and Asia ,such as Vietnam,Thailand , Malaysia and so on . We gained good reputation in the industry because our various items made of imported raw material, good workmanship and fast delivery time. 4. Custom design welcome Customer logo /design/OEM welcome .So our products always so creative&innovative . 5. Best service We keep every customer for long time business.We regard every one as our VIP,no matter small or big order .