Vertical tripod turnstile, tripod turnstile

Vertical tripod turnstile Keywords: turnstile, tripod turnstile, security turnstile, safety turnstile, turnstile gate, access control turnstile, access control gate, access gate, wing barrier, swing barrier, flap barrier, security wing barrier, safety wing barrier, access wing barrier, access barrier, auto gate, arms gate, arms turnstile, rotate gate, rotate turnstile gate, arm fall turnstile gate, pedestian access gate, traffic gate, waist height turnstile, half height turnstile, full height turnstile, speed gate, entrace turnstile, entrance gate
1.Features and Functions
1) The turnstile has fully rainproof stainless steel housing, processed by numeric control     punching and laser drilling, novel and elegant. 2) The turnstile has unique mounting surfaces (for the installation of card reader and indicator light, etc.), ensuring simple and convenient installation of the turnstile control equipment of system integrators.
3) The interior module of the tripod turnstile has a cushioning device for automatic regulation of hydraulic pressure, which helps to realize low noise, no impact and automatic decelerated returning to home position during operation of the turnstile. The interior module has been treated by zinc-plating.
4) Programmable turnstile control is available, for one-direction or bi-direction control (to be set by the user). 5) The base cover can be opened using a key, therefore it is convenient for the user to install it. There are card reader supports at both sides of the turnstile, and a 40CM*18CM mounting plate, for the mounting of controller, is fixed at one side of the housing. 6) The base is fixed with four 10MM expansion bolts.   2. Technical Parameters and Configuration:   Housing: details as mentioned above   Tripod Bar: Length 480 mm, Diameter 40 mm Power Supply: Single-Phase AC110V/220V, 3A, 50/60Hz Control Voltage: DC24V, Power Consumption: 40W Electromagnetism: No Residual Magnetism, without Magnetization Buffer: Hydraulic Pressure Reset Cushioning, without Bumping Noise Operating Temperature Range: -20°C~60°C Operating Humidity Range: 0~95%RH Net Weight: 50kg  Gross Weight: 60kg  Standard Configuration: Stainless Steel Housing: 1 PC (With Supports for Mounting the Controller and Card Reader) Bi-direction Electric Controlled Tripod Turnstile Interior Module: 1 PC AC220V/DC24V Output Power Supply: 1 PC Control Interface Board: 1 PC Bi-direction Electronic Indicating Light: 1 PC Instructions Manual: 1 PC   3. Control Interface Two-Way (PASS1.PASS2) dry contact (or level) control signal input for controlling electromagnets and legal signal indicating lights at the in and out direction
Two-Way (FAL1, FAL2) dry contact (or level) status input for the control of illegal signal indicating light Two-Way DC12V (DOOR1, DOOR2) legal connection, for connecting any kinds of controllers and various consumption devices   4. Turnstile Interior Module
1) The turnstile mechanical interior module is for manual dropping of the tripod bar after the control of the turnstile is released; After a passenger passes the turnstile, another bar of the tripod stays at the level position after it passes the hydraulic pressure cushioning device of the interior module. Then, another passenger can only be released (passing the turnstile) after the control of the turnstile is released again. Pushing of the bar only requires 0.5kg force. 2) The interior module of the electronic turnstile consists of three parts: a) Mechanical Part: (The mechanical structure has been installed and tested to be acceptable before it is delivered, so the user does not need to adjust it.) b) Electrical Part: Open-close Electromagnet: DC24V power supply, one piece of electromagnet at each of the left and right side. (For Two directions). For unidirectional usage, only connect the power supply at one side. Bar Dropping Electromagnet: DC24V power supply; It is in pickup position during power supply, and it is in dropout position during power failure therefore allows dropping of bar. (The position of the electromagnet can be adjusted.)  Micro-active Switch: (Travel Switch) When one bar of the tripod turns 120 degrees, the micro-active switch will transmit the reset signal to the control board, and then the control board sends instructions to reset the turnstile. (One passenger passes)    c) Cushioning Device: An oil buffer (Model: AD1410-5) made in Taiwan is used. The buffer can be used to adjust and control the reset speed of the tripod bar. When the tripod turns too quickly and there is bumping noise, change the value of it from small to large (0-8) until sound result is obtained. The turnstile has been adjusted and tested to be acceptable before it is delivered. After it is used for a certain period and somewhat large bumping noise is heard, you can adjust the buffer appropriately.   Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile Vertical tripod turnstile, tripod turnstile ....